Dec 29 2010
Embellished Tee with Ruffled Front and Cuffs
Remember how I have been improvising with my maternity wardrobe?
Instead of buying a bunch of maternity shirts……I have purchased some knit tees, a size or two bigger than normal, and have embellished them up a bit.
I seriously tire of my maternity shirts. Really quickly.
And sometimes feel grumpy wearing the same ones over and over again.
So this has been the perfect way to add a few new shirts to the maternity closet. And not spend a ton.
Here is the Embellished Tee with Flowers, here.
And the Embellished Tee with Strips, here.
Remember, all of these ideas can be used for non-maternity use too. So if you’re feeling grumpy in your same shirts like I have been (it’s okay, just admit it), head out and find some inexpensive knits to embellish up a bit.
So today……….a ruffled front tee with ruffled cuffs.
A nice and quick way to happy up your mood.
With a sweet multi-layered ruffle down the front, adorned with several buttons.
And similar ruffles along the sides of both cuffs.
Who doesn’t need a little change from their plain ‘ol tee?
TIP: I always hang dry the clothing I have made. (Mostly because I’m tall and don’t want them to shrink up.) But after washing shirts that I have embellished, I pat the embellished part flat, so that it dries in the shape I’d like it…….and then hang or lay the shirt flat to dry. Placing them in the dryer may distort/scrunch up your embellishment, making you very unhappy! :)
Find a knit tee on sale (I found this one at Target), in your closet, or make one yourself (like I did here for another project) to use as your main shirt.
Then, find a few pieces of sheer fabric to use for your ruffle. You can use thicker cotton or knit but it will make it heavier and may pull funny on the shirt because of all the layers. I found these scraps of chiffon/voile/curtain-y material in the scrap bin at Walmart. All were machine washable and they cost me about $1 for more than I needed. I bought two different textures……one has a crinkle to it and the other is just a plain sheer voile. (The crinkle one was made for curtains I’m pretty sure…)
All measurements will be a bit different, depending on tall you are, where you want your ruffle, etc.
But here are the measurements for my ruffle pieces.
I cut three pieces of my sheer fabric to be:
- 9 x 17 inches
- 7 x 17 inches
- 5 x 17 inches
Here’s a more up close shot of the fabric texture…….in case you’re looking for fabrics that are unlabeled in the remnant bin at the store.
Fold each strip in half lengthwise and sew 1/4 inch from the edge. I used a narrow zig-zag stitch and then trimmed off the edge.
Then turn each strip right side out and iron flat. While you’re ironing, place the seam along the backside, but not directly down the middle. (I placed my seam right down the middle but found that it adds more bulk as you’re trying to ruffle the pieces in the future steps. So just offset the seam to the side just a bit…..while still keeping it hidden in the back.)
Then fold under each end a 1/4 inch, another 1/4 inch, then sew in place.
Next, stack your 3 ruffles on top of each other, with the most narrow strip on top. Then sew a basting stitch right down the center of your 3 ruffles. (Need help with basting stitches and gathering? See the post here.)
Gather your stack of strips down to about an 8 inch long ruffle and place on the front of your shirt. I started the ruffle right below the collar and it ends slightly below my bust. Pin in place.
And while pinned, try on the shirt to see if it looks right on you. (Differences in ruffle length will also depend on how low/high of a scoop the collar on your shirt is.)
Then sew a seam right down the center of your ruffle, attaching the ruffle to the shirt. You may need to increase your stitch length just a bit, so you’re not pulling too much on the ruffle or the knit shirt as you go.
Then steam/iron your ruffle flat. Also, if your knit shirt pulled at all while sewing the ruffle to it, steam the shirt from the inside to shrink that knit back up again.
Next, hand sew some buttons on.
For the cuffs, I only made a single layer ruffle for each cuff. So I cut two strips of the chiffon that were 4.5 x 9 inches. I folded, ironed, and sewed up the ends the same way as the ruffles above.
And then ruffled them up the same as above. I attached them to sides of the cuffs, opposite the inner seam of the sleeve. My shirt already had little cuffs on them that were were 4 inches long, so I used that as my guide for how long to make each ruffle. But you don’t have to have a cuff on your shirt to add this detail.
Then I added a few buttons down the center of each ruffle.
I layed the sleeve on the right flat, with the seam along the right side………so you could see how the ruffle placement on the outer edge of the cuff looked.
And that is it.
Nice and simple……..and pretty quick.
Sure helps a drab wardrobe.